My Cart:

0 item(s) - £0.00
You have no items in your shopping cart.

Electro-Fashion, Switched Coin Cell Holder

1.85
This specially designed E-Textiles Coin Cell Holder has large connection points for the conductive thread. It also has an integrated in power switch.

Availability: In Stock.

Code1+ 10+ 500+
2711£1.85
(£2.22 incl VAT)
£1.55
(£1.86 incl VAT)
£1.45
(£1.74 incl VAT)
OR

This specially designed e-textiles coin cell holder from Kitronik has large connection points for the conductive thread.

These are clearly marked to show the battery polarity. The unit also has a small power switch so that you can turn the power on and off.

It uses a very thin PCB material to keep its size to a minimum.This allows it to be easily incorporated into your own e-textiles designs.

Caution: This coin cell holder contains Nickel and should not be used in designs where it will be in prolonged contact with the skin.

The board accepts CR2032 batteries.

Dimensions: L44 x W20 x H4.5mm

For more information and examples showing you how to use these parts in a e-textiles design visit our dedicated e-textiles section.

beanie_standard_led_thumb
How to Add a Standard LED to a Beanie Hat
Learn how to add a standard LED to a beanie hat using conductive thread in our easy to follow tutorial.
beanie_pcb_led_thumb
How to Add a PCB LED to a Beanie Hat
Learn how to add a PCB LED to a beanie hat using conductive thread in our easy to follow tutorial.
bag_with_3_LEDs_thumb
How to Add 3 Standard LEDs to a Bag
Learn how to add three standard LEDs to a bag using conductive thread in our easy to follow tutorial.
etextiles_leds_through_fabric_thumb
Getting Started with E-Textiles: Positioning LEDs Through Fabric
Learn how to position LEDs through fabric in our easy to follow tutorial.
Electro_Fashion_FAQs2
E-Textiles: the Frequently Asked Questions!
So, you have a few questions about E-Textiles - here's a few of our frequently asked questions relating to conductive thread, LEDs, coin cells and how to take care of your wearables.
etextiles_basic_stitches_thumb
Getting Started with E-Textiles: Basic Stitches
Learn about basic E-Textiles stitches in our easy to follow tutorial.

Questions:

Posted by Juan delgado, Wednesday, 8 March 2017 on product Electro-Fashion, Switched Coin Cell Holder
  • 0
    vote
    A:

    Hi Juan, This board would take a 3V coin cell battery and as such could only provide 3V maximum. The coin cell batteries also supply 200mA, and as such if 4 of the LED’s were connected and could supply enough voltage to turn them on, they would only last maybe 30 minutes before the battery was fully drained. You may be better with a power source such as this, https://www.kitronik.co.uk/4652-polymer-lithium-ion-battery-1ah.html.

    Posted by Michael Lockhart on Wednesday, 8 March 2017
Posted by Evie, Thursday, 12 March 2015 on product Electro-Fashion, Switched Coin Cell Holder
  • 0
    vote
    A:

    You can run around 4-5 of the Electro-Fashion Sewable LEDs off a three voltage coin cell battery. They need to be connected up in parallel for the coin cell to power them sufficiently.

    Posted by Michael Lockhart on Thursday, 12 March 2015
Posted by Sam Wilkinson, Wednesday, 5 December 2012 on product Electro-Fashion, Switched Coin Cell Holder
  • 0
    vote
    A: There isn?t a datasheet for the holder, the dimensions are L44 x W20 x H4.5mm. Specifically what data were you looking for? The coin cell is 20mm across, 3.2mm high and has a capacity of 200mA/h. Again what did you need to know?
    Posted by Geoff Hampson on Wednesday, 5 December 2012
Posted by Ian Lewis, Wednesday, 20 June 2012 on product Electro-Fashion, Switched Coin Cell Holder
  • 0
    vote
    A: Yes it takes the CR2032 coin cell. A suitable coin cell is shown in the related products at the top left of the page.
    Posted by Geoff Hampson on Wednesday, 20 June 2012

Ask Your Question

* Required Fields

Related Products