Clearance prices shown in orange are in GBP and exclusive of VAT.
This is a great fun kit that is sure to grab the interest of your students. When thrown the Frisbee will produce a visual display created by the LEDs on the PCB. At the same time the board can also be programmed so that is will produce a sound or play a tune (requires the addition of Piezo element buzzer, not included). When the Frisbee stops spinning the LEDs will turn off and the sound or tune will stop. The Frisbee can be made by vacuum forming.
This kit is a programming based project and as such will require programming.
- PIC Frisbee Kit with Battery.
- The kit uses 2 x CR2032 coin cells which are included.
- 1 x 3.5mm PCB Mount Jack Socket.
- 3 x 330Ω Resistors.
- 2 x 10KΩ Resistors.
- 1 x 22KΩ Resistor.
- 1 x 5mm green LED.
- 1 x 5mm Red LED.
- 1 x 5mm yellow LED.
- 1 x 8 pin IC holder.
- 2 x CR2032 coin cell.
- 2 x CR2032 coin cell holder.
- 2 x Tilt Switch.
- 1 x 10uF capacitor.
- 1 x Frisbee PCB
- PCB Length: 66mm.
- PCB Width: 71mm.
- PCB Height: 1.6mm.
- 2 x CR2032 Coin Cell Battery (Included).
- Soldering Iron.
- Wire Cutters.
- Wire Strippers.
- PICAXE USB Download Cable.
- Click here to download build instructions.
- Click here to download the full teaching notes.
- Click here to download a test program for the Frisbee.
- This Kit Requires Assembly.
- This Kit Requires Programming.
- The kit requires your choice of 8 pin PIC chip (PICAXE or Genie) and optionally a sounder.
Teachers can order a sample of this kit (one per school) here. You will need to select the kit from a list of all the sample kits; the stock code for this kit is 2128.
Note: this service is only offered to schools for evaluation purposes only.
This kit is designed and manufactured in the UK by Kitronik.
|PCB LxW (mm):||71 x 66.|
|PCB Component Count:||16.|
|Voltage Nominal (V):||3.|
|Voltage Range (V):||2.2V - 4V.|
|Standby Current (mA):||0.9.|
|Current max at Nominal Voltage (mA):||35.|
How do I program the PICKAXE chip? What platform and in which language? I'm in Australia, if that makes a difference... Thanks
Posted byon Tuesday, 19 April 2016
We have a resource which should help to show how to program the PICAXE chip, https://www.kitronik.co.uk/blog/use-picaxe/ there is also a link to show where you can download the PICAXE software. It shouldn’t matter that you’re in Australia
Excl. VAT: £2.15 Incl. VAT: £2.58
GP Lithium 3V Coin Cell CR2032. Capacity 200mA/h. Width 20mm height 3....
Excl. VAT: £19.99 Incl. VAT: £23.988
The CS18 18W Soldering Iron (240V AC Mains Supply) is perfect for most...
Price From: Excl. VAT: £0.74 Incl. VAT: £0.888
A low cost miniature Piezo Buzzer with leads. Requires external drive ...
Excl. VAT: £6.90 Incl. VAT: £8.28
DISCONTINUED - This project uses a PICAXE-08 chip & can be used as...
Excl. VAT: £2.10 Incl. VAT: £2.52
Self-assembly board allowing prototyping of PICAXE-08 circuits. A prot...
Excl. VAT: £3.00 Incl. VAT: £3.60
DISCONTINUED - The PICAXE Programming Editor Software allows programs ...